AOpen AK76F-1394 SiS IDE Driver
Note: Please have your SiS VGA driver updated to version R as well. Driver, SiS AGP Driver, Re, /6/4 SiS IDE Driver, Ra, /3/ To do so in Windows 7 and Windows 8, open regedit and navigate to the sis Windows XP Professional IDE 1 reply AK76F AX45F-4DL. Driver, SiS AGP Driver, R, 4/25/, KB. SiS AGP Driver for Win98SE/ME/2K/XP SiS IDE Driver, Ra, 3/17/, KB.
|Supported systems:||ALL Windows 32x/64x|
|Price:||Free* [*Free Registration Required]|
AOpen AK76F-1394 SiS IDE Driver
Overclocking refers to running a component at a speed greater than it was designed for.
RAID Driver download free :: FixDevice
This gives enhanced performance but often at the expense of decreased stability. Intel driver. Intel Network Drivers.
This site maintains listings of network drivers AOpen AK76F-1394 SiS IDE on the web, organized by company. Includes links to useful resources. PC maintenance article - It s a brush based fan, which means it makes noise -particularly when it s cold at bootup. Some also want to replace it to get better cooling.
Main board drivers and free Main board downloads // - - indexed by update date
The most common way of doing this for most chipsets is to use a Blue Orb chipset cooler. To start the mod, I removed the old fan. You have to be careful when taking it off, because the back of AOpen AK76F-1394 SiS IDE board has a lot of leads which can be scratched easily. Just use a needle AOpen AK76F-1394 SiS IDE pliers to clamp the plastic and push it through the hole.
The fan will then remove with ease.
Be careful not to scratch the leads on the back of the board I was surprised to find that Abit actually used thermal compound although a very small amount between the chipset fan and the Northbridge. I didn t think there would be any kind of material AOpen AK76F-1394 SiS IDE at all. Not much thermal compound Then I attached the Blue Orb.
Aopen AK77-400 Max SilentTek utility
I soon found out that the Blue Orb does not fit on the KT7. Because of this, the Blue Orb is short by about half a centimeter. I tried bending it and forcing it AOpen AK76F-1394 SiS IDE the board for about thirty minutes to no avail. There is simply no possible way to get it to fit. Of course you can juse use thermal tape on the bottom without clamping the unit down, but this defeats the AOpen AK76F-1394 SiS IDE of getting the added cooling of the Blorb.
I then tried to mount the Blue Orb s fan on the KT7 s heatsink, since AOpen AK76F-1394 SiS IDE was obvious the Blorb s fan was a tad better. This also was impossible to accomplish without some serious modification. The screws just don t line up, and it s impossible to force the screws into the heatsink believe me I tried.
Mounting the fan on the KT7 s heatsink won t work It is a good idea to take off the current heatsink and fan on the KT7 s Northbridge. Abit didn t use very much thermal paste at all.
It s a good idea to take it off and put a new thin layer of paste over the chip. It s possible this could further increase stability of the board, possibly allowing you to raise the FSB higher.
AOPEN AK76F-400N Online Manual
Since users have asked exactly how to remove the BIOS chip from the board, I have put together a short little guide. The BIOS chip is located on the bottom left of the board.
The writing on the chip not the sticker reads from the LEFT corner of the board - remember this when you put it back in. The chip is in it s socket rather securely.
It s not possible to just lift the chip out with your fingers. You will need to use a flathead screwdriver to pry the chip off.
SIS G/GV PRO driver
If you get AOpen AK76F-1394 SiS IDE lot of resistance, chances are you are trying to pry the BIOS chip s socket off the motherboard, and not the BIOS chip out of it s socket. The chip will pop right out. Be careful when prying because if you pry a little too far the end pins will start to bend. If this happens, just bend them back.
It s obviously better to AOpen AK76F-1394 SiS IDE the situation all together by simply prying the chip off from both ends evenly.